MESNET FARKLILIKLARININ BAZALT ELYAF TAKVİYELİ KOMPOZİT BORULARIN DÜŞÜK HIZLI DARBE DAVRANIŞLARINA ETKİSİNİN İNCELENMESİ

Mehmet Turan DEMİRCİ, Uğur YOZGAT

Öz


MESNET FARKLILIKLARININ BAZALT ELYAF TAKVİYELİ KOMPOZİT BORULARIN DÜŞÜK HIZLI DARBE DAVRANIŞLARINA ETKİSİNİN İNCELENMESİ

Özet

Gerçekleştirilen bu çalışmada, ±55o filaman sarım BTP/Epoksi kompozit borulara iç çapı ölçülerinde dolu çelik mil yerleştirilerek, borunun içinden mesnetleme yapılmıştır. Mesnetle yapılmayan içi boş BTP/Epoksi kompozitler ile birlikte çelik mil ile mesnetlenmiş BTP/Epoksi kompozit boruların 20J ve 25J enerji seviyelerinde düşük hızlı darbe testleri gerçekleştirilmiştir. Gerçekleştirilen testler neticesinde, içi dolu çelik ile mesnetlenmiş BTP/Epoksi ve içi boş BTP/Epoksi kompozit boruların maksimum darbe kuvvetleri, deplasman değişimleri ve absorbe edilen enerji miktarları belirlenmiştir. Mesnetin ±55o filaman sarım BTP/Epoksi kompozitlerin düşük hızlı darbe davranışlarına etkisi tespit edilmiştir. Mesnetleme ile maksimum kuvvet değerinin arttığı, deplasman miktarının da düştüğü belirlenmiştir.

Anahtar Kelimeler: Bazalt elyaf, Filaman sarım kompozit, Düşük hızlı darbe davranışları

INVESTIGATION OF THE EFFECT OF SUPPORT DIFFERENCES ON LOW VELOCITY IMPACT BEHAVIORS OF BFR/EPOXY COMPOSITE TUBES

Abstract

In this study, ±55o filament wound BFR / Epoxy composite tubes have been supported by a steel shaft with placing inside the composite tube according to internal diameters. Low velocity impact tests were performed at 20J and 25J energy levels for BFR / Epoxy composite tubes supported by the steel shaft and unsupported. As a result of the tests, maximum impact forces, displacement changes and absorbed energy amounts of BFR / Epoxy composite tubes supported by the steel shaft and unsupported were determined. The effects of a steel shaft support of ± 55o filament wound BFR/Epoxy composites on low velocity impact behavior were investigated. It was determined that the maximum force value increased and the amount of displacement decreased by the steel shaft support.

Keywords: Basalt fiber, filament wound composite, low velocity impact behaviors.


Anahtar Kelimeler


Bazalt elyaf, Filaman sarım kompozit, Düşük hızlı darbe davranışları

Tam Metin:

PDF

Referanslar


Manikandan, V. ve ark. Investigation of the effect of surface modifications on the mechanical properties of basalt fibre reinforced polymer composites. 2012; 43(2): 812-818.

Zhu, L. ve ark. Frequency features of basalt filament tows under quasi-static and high strain rate tension. 2012;46(11): 1285-1293.

Deák, T. ve T. J. T. R. J. Czigány. Chemical composition and mechanical properties of basalt and glass fibers: A comparison. 2009;79(7): 645-651.

Kim, M. T. ve ark. Study on an oxygen plasma treatment of a basalt fiber and its effect on the interlaminar fracture property of basalt/epoxy woven composites. 2011;42(3): 499-504.

Pavlovski, D. ve ar. CNG cylinder manufacturers test basalt fibre. 2007; 51(4): 36-39.

Kara, M. Düşük hızlı darbe sonrası yama ile tamir edilmiş filaman sarım CTP boruların iç basınç altındaki hasar davranışı,doktora, Selçuk Üniversitesi Fen Bilimleri Enstitüsü, 2012.

Demirci, M. T. SiO2 nanopartikül katkısının yüzey çatlaklı ve çatlaksız bazalt elyaf takviyeli kompozit boruların yorulma davranışlarına etkisi, doktora, Selçuk Üniversitesi Fen Bilimleri Enstitüsü, 2015.

Demirci M.T.; Tarakcioglu, N.; Avci A.: Yakut R. Burst failure of basalt fiber reinforced filament wound pipe. In: 14th International materials symposium (IMSP’2012), 10-12 October 2012, Pamukkale University-Denizli-Turkey.

Demirci M.T.; Tarakçıoğlu N.; Avcı, A.; Akdemir, A.; Demirci, İ.: Fracture Toughness (Mode I) characterization of SiO2 nanoparticle filled basalt/epoxy filament wound composite ring with split-disk test method, Composite Part B 119, 114-124 (2017).

Demirci, M.T.; Tarakçıoğlu N.; Avcı A.: The burst failures of the elliptical surface cracked BFR/Epoxy Composite Pipes, In: 4th International Conference on Advanced Technology&Sciences (ICAT’ Rome), 23-25 November (2016) Rome, Italy.

Arikan, H.: Failure analysis of (±55o)3 filament wound composite pipes with an inclined surface crack under static internal pressure, Composite Structures 92182-187 (2010).

Kara M, Kırıcı M, Tatar AC, Avcı A. Impact behavior of carbon fiber/epoxy composite tubes reinforced with multi-walled carbon nanotubes at cryogenic environment. Composites Part B: Engineering. 2018;145:145-54.

Uyaner M, Kara M, Şahin A. Fatigue behavior of filament wound E-glass/epoxy composite tubes damaged by low velocity impact. Composites Part B: Engineering. 2014;61:358-64.


Madde Ölçümleri

Ölçüm Çağırılıyor ...

Metrics powered by PLOS ALM

Refback'ler

  • Şu halde refbacks yoktur.


Creative Commons License
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.

Selçuk-Teknik Dergisi  ISSN:1302-6178